RGMT FIELD MASTER - Chronograph Watch Manual and Review
OVERVIEW
(MOV'T VD57)
Remarks:
The measurement time indicated by the stopwatch hands move independently of the centre hands.
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water resistance. ALWAYS be certain that your crown is securely screwed down ( Position [0] is secured. Positions [1], [2] and [3] are not secured for water resistance ).
Do NOT unscrew your crown while you are in any environment where moisture is present.
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS UNSCREWED FIRST:
TO UNSCREW
Turn the crown anti-clockwise until it turns freely without tension. GENTLY pull the crown out to the other desired positions for watch setting.
TO SCREW
Push the crown ALL THE WAY IN (towards the watch) THEN begin to turn clockwise until it is securely screwed down.
NOTE: Failure to SECURELY screw down the crown after setting the watch may affect its water resistance.
HOW TO SET THE DATE AND TIME
*Before setting the time, check that the chronograph measurement is stopped.
- Pull out the crown to the position [2]-(1st click).
- Turn the crown clockwise until the preview day's date appears.
- Pull out the crown to the position [3]-(2nd click). when the second hand is at the 12 o'clock position. It will stop on the spot. Set the hands to the desired time of the day (make sure AM/PM is set correctly) by turning the crown.
* When the crown is at the position [3]-(2nd click), do not press any pusher. Otherwise the chronograph hands will move.
- Push the crown back in the position [1] in accordance with a time signal.
* Do not set the date between 9:00 P.M. and 3:00 A.M. , otherwise the day may not change properly. If it is necessary to set the date during the time period, first change the time to any time outside it, set the date and then reset the correct time.
STOPWATCH FUNCTION
- The measurement of time is indicated by the stopwatch hands that move independently of the centre hands and 24-hour hand.
- The stopwatch can measure up to 60 minutes.
- The stopwatch measures in 1/10 second increments.
STANDARD MEASUREMENT
ACCUMULATED ELAPSED TIME MEASUREMENT
Restart and stop of the stopwatch can be repeated by pressing the button A.
SPLIT TIME MEASUREMENT
Measurement and release of split time can be repeated as many times as necessary by pressing the button B.
WATER RESISTANCE
Note that the water resistance chart serves only as a guide (please refer to the water resistance chart on the next page). Actual water resistance may vary depending on a number of factors including water temperature, water salinity, and use under water.
The water resistance of your timepiece may eventually be compromised over time with general wear and tear and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if available to maintain the water resistance of your timepiece. Warranty may be voided if the screw down crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi or steam room where steam may enter the case despite the water tight seals used to protect your watch. This may cause condensation inside your watch which may effect and damage the inner workings of your watch.
| WATER RESISTANCE CHART | 30M/3ATM | 50M/5ATM | 100M/10ATM | 150M/15ATM | 200M/20ATM |
| SPLASH / SHOWERING |  | | | | |
| SWIMMING / BATHING |  | | | | |
| BRIEF SWIMMING/ WATER SPORTS | | | | | |
| PROLONGED SWIMMING / FREEDIVING | | | | | |
| SCUBA DIVING | | | | | |
| PROFESSIONAL DEEP SEA D VING | | | | | |
For more details on operating this timepiece please refer to the enclosed booklet or visit:
IM.RGMT.CO
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download RGMT FIELD MASTER - Chronograph Watch Manual and Review
